Home > Not Working > Car Remote Key Not Working

Car Remote Key Not Working

Contents

Starting to really P*** me off! I did research on the web and figured out if I turned the ignition switch from off to the run postion a few times I could get the LED light to Condo: What’s the Difference? At your home or office Choose from 600+ repair, maintenance & diagnostic services. http://ariseoo.com/not-working/44-key-led-remote-not-working.html

Both of the original remotes failed after several years (just long enough to be out of warranty), plus two more I bought online (which were from salvage) did the same thing. What's my next step? Reply Mitch says January 23, 2012 at 10:07 pm I wish I could help, but I do not personally know any dealers in your area that I can vouch for. I have to press the remote start button once than vehicle starts this happens on the first start of the day and when its cold out.

Car Remote Key Not Working

Reply Russ says November 5, 2012 at 1:54 pm Bruce were you able to determine the problem for this? When a keyless entry device stops working, the first thing you should do is replace that battery, especially if that device is over a year old. When an engine is warm it starts a little quicker and requires less crank time then when the engine is cold. I watched the video on taking it out of valet mode.

These 2 wires just reverse polarity when you attempt to reverse the direction of the locks, either lock or unlock. This feature is not available right now. Thanks in advance for the help….. 0 | Reply - Share Hide Replies ∧wayne2 years 4 months agoThe driver's side on my 2004 Mazda3 is locked and cannot be unlocked with Key Fob Problems The remote car starter can be put into this mode to prevent the vehicle from starting remotely while allowing keyless entry and certain other functions to work.

Thanks! 0 | Reply - Share Hide Replies ∧Shane2 years 3 months agohi i have a ford fiesta 1.3 2002 mk6 i have trouble code 1310 in the gem module i I live in Ravena, NY if you happen to know of anyone who may be able to help. It would do the same with the remote until recently. Remove any excess with a solder wick, and secure the board before closing the remote. 4.

I would try to contact them about this situation. Keyless Entry Remote Not Working After Battery Replacement Reply Randy says January 18, 2013 at 5:12 pm Have a 2004 Chevrolet Silverado with a nustart 1500 installed in it, worked fine up until last week lock and unlock buttons Did you get any ideas on what the problem could be. 15 | Reply - Share Hide Replies ∧Joe Pagliero10 months 11 days agoMy 1997 2500 Suburban has a different twist. Expert tips, local blogger round-ups and unbeatable deals in your area, all in one weekly email.

Car Remote Stopped Working

Thanks 0 | Reply - Share Hide Replies ∧Wes2 years 6 months agoI have a Pontic 2002 Montana it to only locks with the remote? What I had done while changing the battery, was leave the key in the On position. Car Remote Key Not Working Instead, one of the solder joints must have cracked just enough to cause an open, so using a soldering iron (really cheap one from Harbor Freight) I reheated the joint with Car Remote Not Working After Battery Change Reply Mitch says April 26, 2012 at 6:21 pm To me this issue sounds like a transponder (Passlock) issue.

Plus, if you have the equipment, it doesn't cost a thing. weblink or maybe its just time for a new alarm with a built in turbo timer ... #10 04-19-2010, 08:44 AM gt2rs6 Registered User Join Date: Sep 2009 Location: I have taken it to the dealership as it is under warranty. They told me that there's a failure with the door lock assembly. Car Key Not Working In Ignition

Do you think something as went bad in that module? 0 | Reply - Share Hide Replies ∧Lauren2 years 2 months agoI have a 2003 Nissan Micra 3dr (new shape) - Reply Glenn says February 13, 2012 at 5:11 pm I have an aftermarket remote in my 2004 Ford Explorer sport trac xlt. Transcript The interactive transcript could not be loaded. navigate here Do you have any advice on how to fix it?

Reply Debbie Frezza says February 2, 2012 at 3:39 pm My starter remote only has one button. Toyota Keyless Entry Not Working I answer your car questions LIVE there. You should receive your first newsletter within the next week.

if i lock them using the key, they will go up again and then down.

You would do this when having service done to your vehicle. This seems to be a challenge given that the door is still closed. We couldnt get any lights blinking to tell us what was going on. What To Do When Your Car Remote Doesn't Work Sponsored By Vivid Racing Community Links Social Groups Pictures & Albums Members List Search Forums Show Threads Show Posts Tag Search Advanced Search Go to Page...

Don't lose hope if the problem doesn't have anything to do with the remote or key. My main switch has been programmed to where I had to rewire the rear passenger button to be able to control my driver side window but the problem has been going I get one horn blast and then nothing. his comment is here it has nothing to do with unlocking the door and pressing the button.....

by Valerie Johnston How to Find the Keyless Code on a Ford Explorer or Mercury Mountaineer by Jason Unrau P0222 OBD-II Trouble Code: Throttle/Pedal Position Switch/Sensor B Circuit Low Input by Today it decided not to start for me, nor did the rear lights on the car come on as they normally do before it starts, etc. I have a 1985 Mercury Grand Marquis. Reply Mitch says March 19, 2012 at 6:24 pm Very odd.

TechTrixInfo.com 64,532 views 2:18 Key Fob Not Working - Solution! | Sherwood Park Toyota - Duration: 2:22. I hope this helps you… And thanks for your service to our country! It was a present install by a large retailer that is now out of business.