Home > Not Working > Saab 9-3 Radio Wont Turn On

Saab 9-3 Radio Wont Turn On


Factory Car Stereo Repair 86,453 views 4:32 Saab Information Display (SID) Dead Pixel Repair - Duration: 15:01. Reply SA6AYN says: June 10, 2014 at 08:28 If you are lucky it's just the fuse or a loose cable. If the values of several control modules increase, wiring diagrams must be used to see how the control modules are interconnected. The P-bus does not have a wake-up function similar to that of the I-bus.[/FONT] [FONT=Verdana]The two bus leads (a green wire for bus + and a white wire for bus -) Source

Such a lead has a maximum transfer rate of 10 kbit/s. There may also be fuses in the left side of the trunk, behind service door in the lining. The whole thing stops working. Then I read online about a guy that just hit his a couple of times and it started working.

Saab 9-3 Radio Wont Turn On

You still need the right code, though. This deals with mainly a 97, 900SE convertible but should work with allother cars. Note that a long series of zeros is the same as no message being sent.[/FONT] [FONT=Verdana]The P-bus, which has a high data rate, has two wires to reduce its sensitivity to

I did not had any visual corrosion, but I found that there has done some soldering by some earlier owner. All rights reserved. The P-bus has two leads and the I-bus one lead. Saab 9-5 Radio Not Working The owner's manual for the 1996 900 se lists the process that works for this convertible.

Or do some googling to figure out how to bypass it yourself.. Saab 93 Radio Fuse Location permalinkembedsaveparentgive gold[–]ru4serious2000 9-5 Aero 1 point2 points3 points 1 year ago(0 children)Had somewhat of the same issue. Nathandm78 50,945 views 7:37 2006 Saab 9-3 Aero For Sale - Duration: 9:03. With out adding a hidden radio receiver or running it parallel Reply Richard says: January 28, 2016 at 05:44 Hi I have a 2005 TID 9-3, Previous owner removed and under

If you get 4 horizontal lines, then I think you may have the wrong code, call a saab Stealership. Saab Amp1 Bypass Related ContentSaab 9-3 Repair and MaintenanceSaab 9-3 Maintenance ScheduleSaab 9-3 Problems(37)Saab 9-3 Repair EstimatesSaab 9-3 Q&A(264)Saab 9-3 Recalls(17)Saab 9-3 ShopsSaab 9-3 Reviews(9) Car Care AdviceBlogEncyclopedia Most Common Saab 9-3 ProblemsPower Windows I have the 05 9-3 Linear with a 7 speaker ES-2 system. Checked all the fuses and they are all working.

Saab 93 Radio Fuse Location

I've been sick for a while but now I have looked in to my car again. Matte and dull. Saab 9-3 Radio Wont Turn On Immobilization[/FONT] [FONT=Verdana]When the ignition is switched on, the CIM checks that the correct key is inserted in the ignition switch. 2004 Saab 9-3 Radio Not Working To find out where the break is, disconnect then reconnect the battery cable.

or should i get another amp?or getting a new system would be better option? this contact form All O-bus systems will then be initiated at the same time, allowing the ICM to calculate how many control modules sent a light signal, in other words, how far back along Without fault codes is reseating of connectors and replacement of units the only fault tracing measures. I ended up leaving mine bypassed.. 2006 Saab 9-3 Radio Not Working

I could therefore be sure that the AMP1 had a working optical input and power stage. The O-Bus is infact going to tell you information and it's easy to check. There are many cases reported of pins being pushed backwards on the OBD-connector, like the one one STCS: forum.saabturboclub.com • Visa trd - saab 9-5 2002 linear sportcombi obd problem, and http://ariseoo.com/not-working/how-to-fix-a-treadmill-that-won-39-t-turn-on.html Remember Me?

CarGurus | My account Saved searches Saved listings Saved promotions Sign in Join | Advertise | United States Canada United Kingdom Used Cars New Cars Car Values Sell My Car 2003 Saab 9-3 Radio Display Not Working Turns out it was one of the hole links through the PCB near the final power amp stage that had corroded on the top side and had no connection through the Reply With Quote Sponsored Links Remove Advertisements SaabScene.com Advertisements + Reply to Thread Page 1 of 2 1 2 Last Jump to page: Quick Navigation Saab 9-3 Sport Saloon /

All rights reserved.

I have had this for over a year now and i'm getting sick of it. Replacing a door lock module. - Duration: 7:37. Leave car in on position don't start engine 4. Saab Amp Bypass Beyond this, it is extremely difficult to tell without the proper diagnostic tools and virtually impossible to give any good suggestion from afar.

what do you think? abiez 10,915 views 2:24 How to add an Aux Input to a Saab 9-3 USING A PLUG-IN HARNESS!!! - Duration: 10:54. checked all fuses they are good, do you think it might be just the radio? Check This Out Code in should be on the screen if you did not get it one hour ago.

The difference in voltage between the two leads (P-bus) or the lead and ground (I-bus) is either 0 V or roughly 5 V. So, I got the radio replaced and the dash appeared to start working but the radio wouldn't!! Now pull the radio fuse, then pull the radio diagnostic fuse. If you get code in now, do nothing.

Visit AutoGuide.com today. sam1174 234,317 views 11:54 Saab 9-3 Stereo Install! - Duration: 3:02. permalinkembedsaveparentgive gold[–]tonym9782003 Saab 9-3 linear 1 point2 points3 points 1 year ago(0 children)Haha! A potential difference to ground lower than 2.2 V is interpreted as a one, and higher than 2.2 V as a zero.

The placement of the amp under the drivers seat makes it particularly susceptible to damage. Now pull the radio fuse, then pull the radio diagnostic fuse. I'll see if I can find any. I ran a test for faultcodes and I only have one: "CIM b2915 00 ICM Saknas p bussen" (ICM missing on BUS) So my guess is to switch the ICM-unit and

I have several screwdrivers and bags of enthusiasm!!!